Current per 1 LED (mA)

Current of 1 LED in segment (mA) Current of LED in 1 segment.

Dimming system

Programmable

Dimmable

Lm per meter (Lm)

Dimming method

LED package type

Product optionally produced in colour We are able to produce your selected design, in the following colour / spectral properties.

Light source

Surface colour

Output current (mA)

Max. power Voltage (V)

Electrical protection

IP degree

Input Voltage (power supply)

Light distribution Type (diffuser)

LED chip manufacturer

Viewing angle (°)

Cuttability (mm)

El. power (BOOST) (W) El. power in BOOST / Enhanced mode

Total el. power (W)

Colour temperature (primary light source) (K) Correlated Colour Temperature CCT (K) of primary light source : is basically a specific numerical measurable definition of light colour of White spectrum according to black body curve (for example 2700K is Warm white Incandescent light, 3000K is wartm white too, but rather of halogene spectrum, but slightly more coldish etc.

Colour temperature (secondary light source) (K)

Colour rendering index CRI

Lx per meter (Lx)

Max. Length when feed from 1 side (m)

Max. Length @ power (Utyp2) (m)

Max. power dissipation (W)

Installation profile width

Max. current allowed (ma)

Minimum Voltage (V)

Minimum number of LEDs in shortened semgent MASTER LED strips has advantage to shorten the last segment to different number than standard 6 or 7. After shortening the last segment the SP solder shortening pad should be soldered with tiny amount of solder.

Luminous flux (Lm)

LED axial distance (mm)

No. of LEDs/m (ks)

Temperature increase in working condition (°C) Temperature increase caused by el. device heat up while working in normall operation.

Constant Current Drivers

Middle wavelength (nm)

PCB width (mm)

Profile type

Light type

Input voltage (Power supply)

Typical Power Current (Luminaire) (mA)

Typical power current (power supply) (mA)

Typical Power Voltage (power supply) (V)

Certificates

LED strip length on the reel (m)

Features / Additional advantages

Optic typology

External power supply included

Features

Cooling

IK protection

Compatibility with MASTER LED strips Compatibility with MASTER LED strips

Case

Lx@Cube (Lx) Intenzita (Lx) 100mm pasiku meraná luxmetrom v uzavretej čiernej kocke 100x100x100mm pri Utyp. LED pás je položený v strede plochy na bielom matnom stole, Luxmeter na vrchu kocky v osi.

Magnetic power (Kg)

Surface material

Max. ambient temperature - TaMax (°C) Maximum allowable ambient temperature in which the product is safe to run.

Max. allowed input Voltage (V)

Maximum number of LEDs connected This parameter is used mainly for current drivven LEDs (CC) and its power supplies. Power supply has certain minimum and maximu output voltage. The LED string connected to the output should be between these 2 limits. Calculation is carried for LED voltage 3,2V.

Max. allowed current ImaxCC (mA)

Min. no. of powered LEDs This parameter is used mainly for current drivven LEDs (CC) and its power supplies. Power supply has certain minimum and maximu output voltage. The LED string connected to the output should be between these 2 limits.Calculation is carried for LED voltage 3,2V.

UV resistant

Optic

Memory

Max. no. of LED BINs used in product

No. of output channels

Suitable for exterior and moist areas

Fire resistancy

Light transmission (%) Light transmission - the higher the more visible are LED dots and the more light travels out of the light source, however, the less homogenous light effect.

Current (BOOST) (mA) Current in BOOST/Enhanced mode

Mounting type

Type

Luminous flux (Boost) Lm/m (Lm)

Luminous flux Lm/m @ItypCC (Lm)

Type of IDC connection

IN/OUT terminals

Type of plastics Type of plasts such as PE, PVC, PC, PMMA etc. Each type of plast has individual chemical and mechanical properties.

Type of SPI protocol

Typ. nap. napätie Utyp @ItypCC (V) Typické napájacie napätie CC systému (constant current) platné pre Ityp

Cooling of upto (W)

Changeable output parameter

Suitable for installation

Including Light source